Recessed Panel Sink

Recessed Panel Sink
Recessed Panel Sink - Image 2

Width

This is the overall, outside width of the cabinet box.

(610 - 1220)

Height

This is the height Above Finished Floor (A.F.F.), meaning this includes the Toe Kick Height.

The cabinet box height will Height – Toe Kick Height, as shown below being 774mm. You can adjust Toe Kick Height if you turn off Adjustable Legs.

For instance: If you turn off Adjustable Legs and set Toe Kick Height to 0, your carcass height would then equal the full Height.

(700 - 1000)

Depth

This is the depth of the cabinet carcass.

This does not include the thickness of any door or drawer fronts.

(450 - 660)

Toe Kick Height

Toe kick height is always subtracted off of the overall height you enter to calculate cabinet height.

This is adjustable only if you turn off Leg Levelers. By making this number smaller, the cabinet will get taller by the bottom getting closer to the ground. Making it larger will shrink the cabinet by raising the to bottom further away from the floor.

(0 - 457)

Finished Interior

Select to have a the exterior colour for this this cabinet. Exterior colour matches the door colour you selected in Project Setup.

Otherwise, it will have the Carcass material for everything.

Top Drawer Front Height

Adjusting this will automatically adjust the doors or drawers below to equally fill out the rest of the front of the cabinet.

If “Equal Drawer Heights”, on select products, is checked, then this value will be ignored, and all the drawer fronts will be made the same size.

(120 - 200)
(102 - 355)
(150 - 540)

Left Reveal

This is the amount of gap there is from the left side of the carcass to the the edge of the door/drawer front.

Typically this is 1.5mm, so that when you put two cabinets beside each other, the gaps from both cabinets add up to 3mm, which is standard clearance.

If you are putting a flush filler or panel on the left side of this cabinet, you should change it to 3mm, to maintain proper clearance.

(0 - 11)

Right Reveal

This is the amount of gap there is from the right side of the carcass to the the edge of the door/drawer front.

Typically this is 1.5mm, so that when you put two cabinets beside each other, the gaps from both cabinets add up to 3mm, which is standard clearance.

If you are putting a flush filler or panel on the right side of this cabinet, you should change it to 3mm, to maintain proper clearance.

(0 - 11)

Top Reveal

This is the amount of gap that there is from the top of the carcass to the edge of the door or drawer face.

On base cabients, top gaps are usually 6mm so there is clearance for the countertop.

On upper and tall cabinets, top gaps are typically 0mm (flush with top), unless you are putting a flush filler piece or panel above the cabinet, in which case you should change it to 3mm.

If you are stacking cabinets, you want to make sure you have a 3mm gap from one cabinet’s doors, to the others. General recommendation is splitting the gap on each cabinet. This would mean a 1.5mm Bottom Reveal on the top cabinet, and a 1.5mm Top Reveal, on the bottom cabinet. This will ensure proper door gaps.

(0 - 25)

Personalized Labels

Putting a name or number in this spot will help you organize your cabinets and products in a way that makes sense for you and your project.

This text will come through on the product sticker that gets put on the back of every cabinet that is produced in our shop, and will save you time from trying to figure out which cabinets are which.

Here are some examples of the product label, with the personalized label in use. Try to limit your personalized label to a few words, or the last bit of text may get cut off of the label if it is too long.

$274.38

Quantity

Unit conversion

Input length in inches for its value in millimeters.
Inches:
/
Inches:
Millimeters:
To convert from inches (in) to millimeters (mm), simply use the following formula:
millimeters = inches × 25.4

This is because one inch is equivalent to 25.4 millimeters. Therefore, by multiplying the number of inches by 25.4, you can determine its corresponding length in millimeters.
Category:

Description

This is designed to be accessible by wheelchair. You may modify the setting to make sure that the size, panel placement, and recessed depth all fit your area’s Code requirements.
The large panel is removeable to access plumbing.